Showing results: 61 - 75 of 83 items found.
-
MP-50 -
FRANKONIA GmbH
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
CRM 100C -
Scope T&M Pvt, Ltd.
CRM 100C directly measures resistance values with DC current injection under live switchyard conditions.The CRM 100C is specially designed to reliably measure contact resistance of Circuit Breakers, Isolators, Bus Bar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards. It can also be used for testing cables, graphite bars etc.
-
TD4000A -
Ponovo Power Co., Ltd.
TD series testing equipment is a HVDC Test Set consisting of control unit and DC high current output unit. And the TD series HVDC primary injection system includes 3 types, which could output 2000Adc/4000Adc/ 8000Adc and 0.1% high accuracy, suitable to be used for different HVDC testing requirements, such as in HVDC Converting station, or railway transportation line, etc.
-
Bloomy Controls, Inc.
Bloomy's 8-Channel Load Module provides isolated current and voltage measurements for eight on-board 5W loads or for eight off-board 120W loads. With built-in switching for calibration and fault injection, the module provides unsurpassed capability for Mil/Aero applications. The module also provides switching and connections to allow switching between a real load (e.g., actuator, valve, etc.) and the simulated load.
-
HH3502 -
Colluck Company Limited
Double Injection Casing. High Accuracy (basic accuracy 0.5%). 3-1/2 digit Jumbo LCD display 2000 count with symbolic signs and back light. Manual Ranging High Voltage test up to 1000V DC and 750V AC. Higher Current test up to 20A AC/DC. Transistor test. Diode and Continuity check. Measure Resistance up to 20MΩ
-
TWA Advanced Series -
Amperis sl
The TWA advanced series instruments are designed for six-winding resistance measurement and simultaneous three phase on-load tap changer analysis of both the primary and the secondary transformer windings. This is performed with a one singlestep cable setup, with test currents of up to 40A. Each transformer configuration has a special measurement algorithm which is optimized for the fast stabilization of test results. The TWA instruments generate a true DC ripple-free current. Both the injection of the current and the discharge of energy from the magnetic circuit are automatically regulated.
-
TWA Standard Series -
Amperis sl
The TWA standard series instruments are designed to measure the resistance of six coils and simultaneously analyze the three-phase tap changer on load of the primary and secondary transformer coils (provided by model TWA40). This is done in a single cable configuration, with test currents up to 40A. Each transformer configuration has a special measurement algorithm that is optimized for rapid stabilization of test results. The TWA instruments generate a true DC current without ripple. Both current injection and magnetic circuit energy discharge are automatically regulated.
-
HH0308C -
Colluck Company Limited
Double Injection Casing. High Accuracy (basic accuracy 0.3%). 6000 count Jumbo LCD display with symbolic signs. Auto Ranging High Voltage test up to 1000V DC and 750V AC. Higher Current test up to 20A AC/DC. Diode and Continuity Check. Measure Resistance up to 60MΩ. Measure Temperature up to 300c. Measure Frequency up to 600k Hz
-
AL-34WB 10A -
Standard Electric Works Co., Ltd
● Wire length: 1m approx. Silicone insulated wire (700mm) with wire connected to straight input plugs (150mm PVC wire), and wire for clamp (150mm PVC wire).● Outside diameter of silicone insulated wire: 6.4mm Outside diameter of PVC wire: 4mm● Input plug color: Red•Green•Black•Blue ● Current rating: 10A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V
-
AL-34WB -
Standard Electric Works Co., Ltd
● Wire length: 1.2m approx. Silicone insulated wire (1000mm) with wire connected to straight input plugs (130mm PVC wire), and wire for clamp (100mm PVC wire). ● Outside diameter of silicone insulated wire: 5mm Outside diameter of PVC wire: 3.5mm● Input plug color: Red•Green•Black•Blue ● Current rating: 5A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V
-
GDJB-PC -
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1.GDJB-PC Universal Secondary Injection Relay Test Set is applied to test the relay unit in relay protection system. 2.At the same time GDJB-PC Universal Secondary Injection Relay Test Set could be considered as a universal three phase AC/DC voltage source or current source. 3.It can work alone or connected to computer, inside the relay controller there are new speed digital signal mini PC and real DAC (Digital-to-Analog Converter) template with new high fidelity and high power, the machine has large panel screen and rotating mouse. It is small in volume, high precision.
-
Computec SRL
- Laboratory of electrical tests and measurements- Injection of voltages and currents. - Megger SMRT33 Triphasic Case- Protection relay test- Tests with class 0.2 instruments - Fluke N5K 3PP50IP Norma 5000 High Precision Power Analyzer- Verification of energy meters- Fault Recorder Verification- Verification of Power Quality Analyzers- GPS verification
-
Denso EMCES
Our sophisticated technology can meet the diversified needs of customers. Component Tests: Immunity, Radiated Immunity, ALSE, TEM cell, Bulk Current Injection, Stripline, Conducted Immunity, Transient Immunity, Power Supply Variations, Electrostatic Discharge Emissions, Radiated Emissions, Conducted Emissions, Transient Emissions. Vehicle Tests - Radiated Immunity, Radiated Emissions.
-
Vanguard Instruments Company, Inc.
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers. The PCI-600 is versatile and can also be used in many other applications that require a high-current source.
-
TD2000A -
Ponovo Power Co., Ltd.
TD series testing equipment is a High Voltage DC Test Set consisting of control unit and DC high current output unit. And the TD series HVDC primary injection system includes 3 types, which could output 2000Adc/4000Adc/ 8000Adc and 0.1% high accuracy, suitable to be used for different HVDC testing requirements, such as in HVDC Converting station, or railway transportation line, etc.
